| 4g61t.org http://4g61t.org/forum/ |
|
| WTB : VR4 AMG CAMS and N/A INTAKE MANIFOLD http://4g61t.org/forum/viewtopic.php?f=67&t=31957 |
Page 1 of 1 |
| Author: | BillyBoBBizWorth [ Tue Mar 09, 2010 3:28 pm ] |
| Post subject: | WTB : VR4 AMG CAMS and N/A INTAKE MANIFOLD |
Hey guys, im after some lumpy cams for my 61T,and ive tracked down what i want, and that is some VR4 AMG cams. the for specs for these cams are : Inlet : 260 degree's Exhaust : 264 degree's im after a pretty good condition set, but any suggestions will be appreiated. Also after the N/A intake manifold that is found of the AMG tuned N/A 4G63's. CHeers |
|
| Author: | Mechacode [ Tue Mar 09, 2010 4:43 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
Good luck, those things are very rare. you'd be better off getting a set of aftermarket 264/264 cams. |
|
| Author: | CaptainTonus [ Tue Mar 09, 2010 4:43 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
Haha, good luck finding a set of these. The AMG VR4's were only sold in Japan, and in very limited numbers. 2nd what mechacode said. The AMG VR4's are all naturally aspirated, thus their cams aren't really designed for a forced induction motor. You'd be better off just getting some upgrade cams for a 4g63t as they will bolt right in to the 4g61t. |
|
| Author: | COBHC [ Wed Mar 10, 2010 2:59 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
The only person I know of that has access to an AMG is Bazeng on gvr4.org, you might want to start there. http://www.galantvr4.org/ubbthreads/sho ... =0&fpart=1 |
|
| Author: | to4garret [ Wed Mar 10, 2010 8:56 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
And i HIGHLY doubt bazeng will sell them. Plus there is no such thing as a FACTORY AMG VR4, all AMG's were NA. |
|
| Author: | COBHC [ Thu Mar 11, 2010 3:28 am ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
Touche lol. I was just trying to point the OP in the right direction. |
|
| Author: | COBHC [ Sun Apr 04, 2010 4:31 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
Hopefully its not too late, I just saw this on gvr4.org. http://www.galantvr4.org/ubbthreads/sho ... =0&fpart=1 |
|
| Author: | 89Mirageman [ Sun Apr 04, 2010 7:18 pm ] |
| Post subject: | Re: WTB : VR4 AMG CAMS (MINT) |
Mark (tkrperformance) on here has a 94 Galant GS engine that he's building as well. I highly doubt that he is going to use the stock cams so I'm pretty sure he would let them go. |
|
| Author: | BillyBoBBizWorth [ Thu May 27, 2010 9:08 am ] |
| Post subject: | Re: WTB : VR4 AMG CAMS and N/A INTAKE MANIFOLD |
Still after these parts. |
|
| Page 1 of 1 | All times are UTC-05:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|