4g61t.org

Specializing in the 3g CSM
It is currently Sun Dec 01, 2024 4:32 pm

All times are UTC-05:00




Post new topic  Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Wed Jan 28, 2015 4:57 pm 
Offline
Member

Joined: Fri Dec 15, 2006 9:36 pm
Posts: 194
Location: connecticut
I have a noise when I launch the car. After looking around I see that the driveshaft is hitting the floor. If I push on the shaft the rubber support for the carrier bearing allows the shaft to move far enough for the shaft to hit. The carrier bearings are the original ones from the 94 Eclipse. The original is available everywhere but i would bet the shaft will still hit the floor. The carrier bearing supports are sagging in my car so if I put new ones in the shaft will be closer to the car. Unless the rubber support on the new ones are much stronger than my whooped out 20 year old ones.

I see that Torque Solution makes a kit to replace the original with a non- rubber support style carrier bearing but I wonder if I will get vibrations at highway speeds. Is anybody using the Torque Solutions carrier bearing and if so how do they work? I like the idea of stabilizing the drive shaft but the originals were rubber for a reason, I would think. Here is a link to this product

http://www.ebay.com/itm/Torque-Solution ... 2d&vxp=mtr

Here is another company who makes a solid replacement

http://www.ebay.com/itm/DSM-DRIVESHAFT- ... 8b&vxp=mtr

What are you guys using?


Top
   
PostPosted: Wed Jan 28, 2015 5:29 pm 
Offline
Moderator
User avatar

Joined: Wed Jan 04, 2006 1:21 pm
Posts: 2142
Location: Tucson Az
I did this back in 05 when my 90 talon would slap the floor pan hard under launch... once done I could launch at 5800 and it never hit again... main thing is to make sure u have it resting on something to support the shaft and let the carrier sit natural that way the silicone gets evenly all the way around it..


go here... http://www.vfaq.com/index-main.html at the top click on drivetrain...scroll down till u see the one that says.. Drive shaft Thump Fix with Pictures.


hope this helps.


Steve

_________________
Steve 89 colt 2.3 stroker stock top end. evo3@20 psi 13.489@99.30mph 3/10 2012
On drag radials.auto trans.launching @ 5 psi and no traction thru 2nd.


Top
   
PostPosted: Thu Jan 29, 2015 10:50 am 
Offline
Member

Joined: Fri Dec 15, 2006 9:36 pm
Posts: 194
Location: connecticut
Thank you very much. I just did the fix and will post results when it is done.
The link has a ton of info, I know what my reading list will consist of for the near future!!!!
Mark


Top
   
PostPosted: Fri Jan 30, 2015 3:43 pm 
Offline
Some call me a god

Joined: Mon Sep 24, 2007 5:50 pm
Posts: 1220
Location: Htown, TX
Have you filled the supports yet? If not, do that, it will limit the slack and movement.


Top
   
PostPosted: Fri Jan 30, 2015 3:52 pm 
Offline
CSM Junkie
User avatar

Joined: Sat Sep 22, 2012 6:40 pm
Posts: 667
Location: Indianapolis, IN
I ordered new ones from Amazon. replaced u-joints at the same time. Less than $150 and you get a whole new driveshaft. Takes about 2 hours

_________________
Thom
1991 GVR4 1025/2000 (PTE 1200's, 16g, DSMLink v3, gm-maf, eagle/ross, .020 over, 272's, EVO VIII Wheels)
1992 GVR4 866/1000 (getting everything from above)


Top
   
PostPosted: Sat Jan 31, 2015 9:58 pm 
Offline
Member

Joined: Fri Dec 15, 2006 9:36 pm
Posts: 194
Location: connecticut
Quote:
I ordered new ones from Amazon. replaced u-joints at the same time. Less than $150 and you get a whole new driveshaft. Takes about 2 hours
I filled my carrier bearings and, now with the driveshaft installed, I can't push it far enough to hit the floor. My carrier bearings were cracked very badly. The silicone squished out multiple cracks in the rubber. I did see a crazy low price on 2 carrier bearings on Amazon. I will get them and get them ready for install before drag race season starts. I was thinking of bringing the new bearings to a local windshield place and have them filled with poly eurothane. I would think it would work just as good and last much longer.

Thanks slowdsm for the link!!!!!
Mark


Top
   
PostPosted: Sun Feb 01, 2015 3:29 am 
Offline
Moderator
User avatar

Joined: Wed Jan 04, 2006 1:21 pm
Posts: 2142
Location: Tucson Az
no problem man.. always here to help when I can.


Steve

_________________
Steve 89 colt 2.3 stroker stock top end. evo3@20 psi 13.489@99.30mph 3/10 2012
On drag radials.auto trans.launching @ 5 psi and no traction thru 2nd.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 7 posts ] 

All times are UTC-05:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Limited