4g61t.org

Thanks CSM Shaun!,

I finally installed those bolts that you sent me (awhiiile back)!
They were a little longer than my origs but did the trick with a washer:


To avoid scroll nauseau , I'll keep the ongoing WTB @ 1st post of this thread here:
http://www.4g61t.org/forum/viewtopic.ph ... 88#p225888

Thx again,
#89

Hey there,

Just wanted to say that I grabbed a couple PS oh $h!+ handles today at the yard.
They are both available for purchase.

Also, the 8 push rivets you need, I need them as well & haven't had any luck buying new ones from the dealer (Dodge or Mitsu) since they are discontinued. I'm thinking of ordering some similar ones that are gloss black and come as a set of 25 for $13 then selling the spares.

Regards,
-Shawn

maroonmetallic - Thx. IM/PMd.

Updates HERE: http://www.4g61t.org/forum/viewtopic.php?f=4&t=28565

Updated Below...

_________________
#89

Sorry for flaking out on the first post I made to you, however,
I just pulled my 1.5 out of my car to do a 63 swap... so I could help you out on the following:

1.5 ECU (little seepage but still works, could use rebuild)

-(8) '2 part missile-looking male clip fasteners' (98 style S-series cars use some that will fit! call me the guinea pig)
-(1) Gray Cargo/Hatch/Parcel shelf (Still at a yard by me.. I can get it for pretty cheap but the wings are a bit rough)
-(1) 4G15 12 Valve lower timing cover & bolts (pulling my 1.8L bits off to keep then parting the motor before scrap!).

You have prices in mind for any of it?
-Shawn

I want the struts! PM me a price shipped to 60185.
Thanks,
Eric

Hi Shawn (Maroon),
No prob... sent IM... thing is I'm awful with wheeling/dealing shoot me a number/numbers on email thedigitalplan(at)optonline.net Thx!

Eric (Turbo),
Sent you an IM.

Thx,

_________________
#89

Updated: January 1, 2010 -
Aaack! My 4G15 Blinker/headlight stalk just broke/is cr@pping out - can use one ASAP!
PayPal is Ready... Email best/quickest: thedigitalplan(at)optonline.net Thx!

and (ongoing)...

Wanted to Buy (or trade* for stuff further down):
-(8) Rear trunk inside plastic '2 part missile-looking moulding/shroud male clip fasteners' (will post pic soon)
-(1) Rear right unboltable stock 1.5 driver seat bracket 'tab' w/ two bolts.
-(2) Rear trunk inside plastic off-white clip fasteners (will post pic soon).
-(1) Gray Cargo/Hatch/Parcel shelf.
-(1) 4G15 12 Valve (plastic) bottom/lower timing cover and corresponding bolts.
-(2) stock lug nuts

FS or *trade (Pics below):
-Stock 4G15 Injectors on fuel rail $29
-Stock 4G15 Intake & TB $21
-Never Used CSM Axle. Part# p82 c8173 $33
-(2) New 'ACME/Unknown brand' CSM Front Struts $24
-4G15 Head for rebuild (was 'Interfered' on vehicle orig w/ snapped timing belt)! $14
-All other stuff in pics (block off plate, hardware, etc.)
-More Stuff in garage... will post as I find!



Got/No Longer Needed:
-(2) short bolts for auto seat belt 'triangle bracket' (could fit in envelope?)
will pay $7 + 3 shipping. !Thx CSM Shaun!
-(1) Driver Side base model seatrails and bolts.
will pay $40 + 6 shipping !All set- Fixed the original rails!
-(1) Trick or link to instructions of getting broken key out of door lock. !Figured Out!
-(1) Gray Oh sh!t bar/handle passenger side. (Color Matched Headliner to dash, deleted handle).

Thanks ,
Thx,

_________________
#89