4g61t.org

Specializing in the 3g CSM
It is currently Thu Mar 28, 2024 1:42 pm

All times are UTC-05:00




Post new topic  Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Sat Aug 17, 2013 11:25 am 
Offline
Member

Joined: Mon Nov 12, 2012 11:54 am
Posts: 43
Location: New Harmony, IN
Finally getting around to working on the 1991 Dodge colt I have. It was an unfinished project when I got it, I'm pretty much down to paint and wiring.
It's getting an Megasquirt 1 setup using the stock cas and ignitors/coils/wires.... Got it assembled, tested, and a unterminated harness.
Printed out all the ecu pinouts a could find and headed to the car, only to find out nothing I had helped.
This is all I have hanging in the passenger kick panel.
Image
Any ideas on what these are?

Also where would the starter relay be located if the car had one? Right now the starter is not hooked up and there is next to no quotes in the engine bay other than a fuse box on the passenger side fender.

Thanks
Randy


Top
   
PostPosted: Sat Aug 17, 2013 11:49 am 
Offline
Spends Too Much Time Under The Hood
User avatar

Joined: Fri Jul 25, 2003 4:57 pm
Posts: 212
Location: Albany, OR
9 times out of 10, if your starter isn't clicking or cranking its because the exciter wire is disconnected. But I could be totally off due to it being a project. What engine is in it? Is it a swapped car?

_________________
2012 Explorer Limited
1989 Colt GT clone 4G63t auto
1992 Talon TSi
1990 Talon TSi
1995 Crown Vic
1993 Ford F-250 BBF
1987 Chevy Sprint Turbo


Top
   
PostPosted: Sat Aug 17, 2013 3:57 pm 
Offline
Member

Joined: Mon Nov 12, 2012 11:54 am
Posts: 43
Location: New Harmony, IN
Checked wires hanging with a meter, found the fuel pump wire, 12v, and switched 12v.
Found the cranking hot write for the starter hanging in the engine bay. Right now the starter is disconnected completely and I don't see starter relay anywhere.
Going to pick one up tomorrow, but as of now it is looking like I won't have a clutch safety switch out any of the stock gauges or warning lights.

Yes, it's a swap in progress.
4g63 4 bolt I think with regrinds.
Arp head bolts
balance shaft removed
550 injectors
65mm throttle body
255 fuel pump
91 turbo trans and a 5 lug conversion
turbo is just a small 60/48 t3 from a Ford 2.3

I'll post some pictures of the mess later tonight or tomorrow.


Top
   
PostPosted: Sat Aug 17, 2013 5:01 pm 
Offline
The Silent Administrator
User avatar

Joined: Wed Dec 24, 2003 3:32 pm
Posts: 9524
Location: Ottawa, ON, Canada
Hopefully you have been here already.
Posted sticky at the top of each forum page IIRC.

www.lilevo.com/mirage/


Top
   
PostPosted: Sat Aug 17, 2013 6:04 pm 
Offline
Member

Joined: Mon Nov 12, 2012 11:54 am
Posts: 43
Location: New Harmony, IN
Yep, went there, printed out a ton of stuff. But I'm not sure what year anything is on this thing as it has been around the blocks few times ;)
As it sits now.
Image
Image
Image

Both my little hatches together.
Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 5 posts ] 

All times are UTC-05:00


Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Limited